TRENDnet TEW-510APB Router Manual (Setup & Configuration)

There is no better technical help than having the manual of any given product. Fortunately, we are presenting router guide for TRENDnet TEW-510APB router. If you need help on topics like web panel access for management, router hard reset, parental control settings, band width allocation, changing your router IP or password from default, port forwarding, then reading this guide is a must.

Page 1 / 12
Copyright ©2005.
All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEW-510APB
Version 05.19.2005
Super A+G Access Point Quick Installation Guide
Point d'accès Super A+G Guide d'installation rapide
Super A+G Access Point Kurzanleitung zur Installation
Punto de Acceso
Súper A+G Guía de instalación rápida
Точка доступа Super A+G
Руководство по быстрой установке
Page 2 / 12
Table of Contents
English
......................................................................................................
Troubleshooting
...........................................................................................
1
1
2
3
5
8
1. Prepare for Installation
......................................................................
2. Install Hardware
................................................................................
3. Configure TCP/IP Settings
................................................................
4. Configure the Access Point
...............................................................
Page 3 / 12
Thank you for purchasing TRENDnet's TEW-510APB Super A+G Access Point
This guide will help you set-up your Access Point quickly and easily. Just follow
the step-by-step instructions below, and enjoy the benefits of accessing the
Internet without ever being tied down to wires" If you run into problems, please
refer to the Troubleshooting section. If you need further technical support,
please visit www.TRENDNET.com or call technical support by phone.
Verify Equipment
Before setting up the Access Point, you should have:
1.
A Computer with a Wired
(Rj45) or Wireless network card.
2.
TCP/IP protocol installed on the Computer.
3.
A Web Browser such as Internet Explorer (5.0 or higher) or
Netscape Navigator (4.7 or higher).
4.
A Hub or Switch connecting your existing wired network.
5.
An RJ-45 Network Cable for connecting the Access Point to your
network Switch.
Verify Package Contents
Please make sure you have everything in the box:
1
External Power Adapter
1.5M RJ45 cable
CD-ROM (User’s Guide)
Quick Installation Guide
TEW-510APB
1. Prepare for Installation
English QIG
English
TRENDnet
TEW-510APB
Page 4 / 12
2
1.
Locate an optimum location for the Access Point. The best place for the
Access Point is usually at the center of your wireless network.
2.
Connect the RJ-45 network cable to the Access Point, then connect the
other end of the network cable to a Switch or Hub. The Access Point is now
connected to your 10/100Mbps network.
3.
Connect the power adapter to the Access Point. Make sure you use the
power adapter supplied with the Access Point; using a different power
adapter may damage the unit.
2. Install Hardware
Check to make sure the following Access Point front panel lights are on: Power,
LAN, WLAN.
Verify Hardware Installation
NOTE:
If you are using a wired computer to configure the Access Point,
please connect this computer to the same Switch or Hub the
TEW-510APB is connected to.
POWER
LAN
WLAN
2
TEW-510APB
English
3
Page 5 / 12
3
3. Configure TCP/IP Settings
Before the Access Point can be accessed and configured, the computer's
TCP/IP settings need to be changed. (That includes your wireless card's IP
address, too.)
English
Windows 2000/XP
1.
Find the
Start
button located on the Desktop.
2.
Click
Start
, and click on
Control Panel
.
For Windows 2000, click Start,
highlight Settings, and click
Control Panel
.
3.
Double-Click the
Network Connection
icon.
4.
Right-Click on the
Local Area Connection
icon, then click on
Properties
.
The Local Area Connection Properties box will appear.