TP-Link Archer D5 v2 Router Manual (Setup & Configuration)

There is no better technical help than having the manual of any given product. Fortunately, we are presenting router guide for TP-Link Archer D5 v2 router. If you need help on topics like web panel access for management, router hard reset, parental control settings, band width allocation, changing your router IP or password from default, port forwarding, then reading this guide is a must.

Page 1 / 2
Verify that the hardware connection
is correct by checking these LEDs.
4
Note:
1. The ADSL LED
takes about 1 to 2 minutes to stabilize.
2. If the
Wireless
LED
is off, please press the Wi-Fi button on the rear
panel for 2 seconds, then check the LEDs again in a few seconds.
Power On
On
Wireless
On
ADSL
Quick Installation Guide
Connecting the Hardware
ADSL Splitter
Phone Jack
Connect to the phone (Optional)
2
Connect the modem router to the
ADSL splitter.
3
Turn on the modem router.
Power Adapter
If you don’t need the phone service, just directly connect the modem router to
the phone jack with a phone cable, then follow steps 3 and 4 to complete the
hardware connection.
1
Connect the ADSL splitter
to the phone jack
Modem Router
AC1200 Wireless Dual Band
Gigabit ADSL2+ Modem Router
7106505572
REV3.0.1
D5
Page 2 / 2
Configuring the Modem Router
LED Indicators
Tether App
USB Features
FAQ (Frequently Asked Questions)
Wired
Wireless
Connect wirelessly by using the SSID (network name) and Wireless Password printed on the
product label at the bottom of the modem router.
Connecting your computer to the modem router (Wired
or Wireless)
Configuring the modem router via a web browser
Select your ISP from the
ISP List
or select
Other
if you can’t find your ISP, then
click
Next
. Follow the step-by-step instructions of the Quick Setup to complete
the initial configuration.
D
Select your
Region
and
Time Zone
, then click
Next
.
C
Enter the password you created and click
Log in
.
Launch a web browser and type in
http://tplinkmodem.net
or
192.168.1.1
Create a new password (1-15 characters) and click
Save
.
1.
2.
B
A
http://tplinkmodem.net
Use the USB port for media sharing, storage sharing and printer sharing across your
local network. You can also setup an FTP server to access your files remotely through
the Internet.
Remote Access
via FTP Server
Printer Sharing
Local Storage
Sharing
Media Sharing
To learn more about the USB features, visit http://tp-link.com/app/usb or simply scan the QR code.
Q1. What can I do if the login page does not appear?
A1.
Make sure the computer is connected to the modem router properly.
A2. If the computer is set to a static or fixed IP address, change it to obtain an IP address
automatically from the modem router.
A3. Verify
http://tplinkmodem.net
is correctly entered in the web browser and press
Enter.
A4. Use another web browser and try again.
A5. Reboot your modem router and try again.
A6. Disable and enable the active network adapter.
Q2. What can I do if I cannot access the Internet?
A1. Make sure the telephone and Ethernet cables are plugged in correctly.
A2. Try to log into the web management page of the modem router using the default
address at http://tplinkmodem.net. If you can, try the following answers. If you cannot,
change your computer to obtain an IP address automatically from the modem router.
A3. Consult your ISP and make sure all the VPI/VCI, Connection Type, account username
and password are correct. If they are not, please replace them with the correct settings
and try again.
A4. Restore the modem router to its factory default settings and reconfigure the modem
router by following the instructions in this Quick Installation Guide.
A5. Please contact our Technical Support if the problem still exists.
Q5. What can I do if the ADSL LED
does not turn solid on?
A1.
Check your cables and make sure they are all plugged in correctly, including the
telephone lines and power adapter.
A2. Manually change your DSL settings. Log into the modem router’s web management
page. Go to
Advanced > Network > DSL Settings
, change the
DSL Modulation Type
to
G.dmt
, and click
Save
. You will be prompted a disconnection, and click
Yes
to
continue. If this cannot work, try to change the
DSL Modulation Type
to
ADSL2
.
A3. Restore your modem router to its factory default settings.
A4. Remove the ADSL splitter, directly connect the modem router to the phone jack and
then reconfigure the modem router by following the instructions in this Quick
Installation Guide.
A5. Contact your ISP to verify if the ADSL line is in good status.
A6. If you have tried all the suggestions above and the problem still exists, contact our
Technical Support.
Q4. What can I do if I forget my password?
Web Management page password:
Restore the modem router to its factory default settings and then set a new password
using 1-15 characters.
Wireless Network password:
A1. The default Wireless Password/PIN is printed on the product label of the modem
router.
A2. If the default wireless password has been changed, log into the modem router's web
management page and go to
Basic > Wireless
to retrieve or reset your password.
Ethernet cable
Note: For advanced settings, please refer to the User Guide on TP-LINK official website at www.tp-link.com.
Note: If the login page does not appear, please refer to FAQ->Q1.
Note: For subsequent logins, use your password you have created.
Note: Per FCC regulations, all Wi-Fi products marketed in the U.S. must be fixed to the U.S. region only.
TP-LINK Tether app lets you conveniently access the modem router and:
View information about the clients on your network.
Block network access from specific users or devices.
Set up Parental Control with access time and content restrictions.
Change the basic wireless network settings easily.
Scan the QR code and download the TP-LINK Tether App from the
Apple App Store or Google Play.
1.
2.
3.
Ensure your smart device is wirelessly connected to your home network.
Launch the Tether app and start managing your home network.
How to begin?
High
Middle
Low
Save
United Kingdom
(GMT) Greenwich Mean Time: Dublin, Edinburgh, London, Lisbon
Region:
Time Zone:
Next
USB Sharing Port
©2015 TP-LINK
Confirm Password
New Password
Q3. How do I restore the modem router to its factory default
settings?
A1. With the modem router powered on,
use a pin to press and hold the
RESET
button on the rear panel of the modem
router for 8 seconds until all LEDs turn
off momentarily, then release the
button.
A2. Log into the web management page of the modem router, and go to
Advanced >
System Tools > Backup & Restore
,
click
Factory Restore
and wait until the reset
process is complete.
RESET Button Use a Pin to Press & Hold 8 seconds
2
LED
Status
Indication
(WPS)
On
(LAN)
Off
On
Off
On
On
(ADSL)
Flashing
Off
(Internet)
(Wireless)
Off
On
(Power)
(USB)
Off
On
Flashing
On
Flashing
Off
System initialization complete.
System initializing or firmware upgrading is in process. Do not disconnect or
power off the modem router.
Power is off.
ADSL line is synchronized and ready to use.
The ADSL negotiation is in progress.
ADSL synchronization failed.
Internet connection is available.
No Internet connection or the modem router is operating in Bridge mode.
The wireless 2.4GHz or 5GHz band is enabled.
The wireless function is disabled.
At least one LAN port is connected.
No LAN port is connected.
The USB device is identified and ready to use.
The USB device is being identified.
No USB device is plugged into the USB port.
A WPS synchronization is established.
A wireless device is trying to connect to the network via WPS. This process
may take up to 3 minutes.
A WPS synchronization has been established for more than 5 minutes or a
WPS synchronization failed.
Flashing
Off