NETGEAR WG602v3 Router Manual (Setup & Configuration)

There is no better technical help than having the manual of any given product. Fortunately, we are presenting router guide for NETGEAR WG602v3 router. If you need help on topics like web panel access for management, router hard reset, parental control settings, band width allocation, changing your router IP or password from default, port forwarding, then reading this guide is a must.

Page 1 / 120
202-10060-01, September 2004
202-10060-01
September 2004
NETGEAR
, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Phone 1-888-NETGEAR
User’s Guide for the WG602
v3 54 Mbps Wireless Access
Point
Page 2 / 120
2
202-10060-01, September 2004
NETGEAR, INC.
Technical Support
Please register to obtain technical support
. Please retain your proof of purchase and warranty
information.
To register your product, get product support or obtain product information and product
documentation, go to
www.netgear.com
. If you do not have access to the World Wide Web, you can
register your product by filling out the registration card and mailing it to NETGEAR customer
service.
You will find technical support information at:
www.netgear.com/support/main.asp
through the customer service area. If you want to contact
technical support by telephone, see the support information card for the correct telephone number
for your country.
© 2004 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR is a registered trademark of NETGEAR, INC. Windows is a registered trademark of Microsoft
Corporation. Other brand and product names are trademarks or registered trademarks of their respective
holders. Information is subject to change without notice. All rights reserved.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the
right to make changes to the products described in this document without notice. NETGEAR does not
assume any liability that may occur due to the use or application of the product(s) or circuit layout(s)
described herein.
Page 3 / 120
202-10060-01, September 2004
3
Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause undesired
operation.
Note
:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Requirements
WARNING!
To ensure compliance with FCC RF exposure requirements, the antenna used for this device
must be installed to provide a separation distance of at least 20 cm (8 in) from all persons and must not be
co-located or operating in conjunction with any other antenna or radio transmitter. Installers and end-users
must follow the installation instructions provided in this user guide.
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
Warning!
To comply with the FCC’s
exposure requirements you must
maintain a distance of at least 1
cm from the antenna of this
device while it is in use. This
device should not be co-located
with other transmitters.
NETGEAR 54 Mbps Wireless Access Point WG602 v3
Page 4 / 120
202-10060-01, September 2004
4
Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 2.4 GHz frequency range. FCC requires this
product to be used indoors in 2.4 GHz the frequency range to reduce the potential for harmful interference to
co-channel Mobile Satellite systems.
Regulatory Compliance Information
This device is restricted to indoor use due to reduce the potential for harmful interference to co-channel
Mobile Satellite and Radar Systems.
Canadian Department of Communications Compliance Statement
This Class B Digital apparatus (54 Mbps Wireless Access Point WG602 v3) meets all the
requirements of the Canadian Interference Causing Equipment Regulations.
Cet appareil numerique del la classe B respect les exigences du Regalement sur le material broilleur du
Canada.
This device comples with Class B limits of Industry of Canada. Operation is subject to the following two
conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause undesired
operation.
The device is certified to the requirements of RSS-139-1 and RSS-210 for 2.4 GHz spread spectrum devices.
The use of this device in a system operating either partially or completely outdoors may require the user to
obtain a license for the system according to the Canadian regulations. For further information, contact your
local Industry Canada office.
Page 5 / 120
202-10060-01, September 2004
5
CE Declaration of Conformity
For the following equipment: 54 Mbps Wireless Access Point WG602 v3
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC),
Low-voltage Directive (73/23/EEC) and the Amendment Directive (93/68/EEC), the procedures given in
European Council Directive 99/5/EC and 89/3360EEC. The equipment was passed. The test was performed
according to the following European standards:
EN 301489-1 V1.2.1 (2000-08)
EN 301 489-17 V1.1.1 (2000-09)
EN60950 / EN300328
0984
!