NETGEAR WG302 Router Manual (Setup & Configuration)

There is no better technical help than having the manual of any given product. Fortunately, we are presenting router guide for NETGEAR WG302 router. If you need help on topics like web panel access for management, router hard reset, parental control settings, band width allocation, changing your router IP or password from default, port forwarding, then reading this guide is a must.

Page 1 / 128
July 2005 v3.0
202-10008-03
July 2005
NETGEAR
, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Phone 1-888-NETGEAR
Reference Manual for the
NETGEAR ProSafe Wireless
Access Point 802.11g WG302
Page 2 / 128
ii
July 2005 v3.0
Technical Support
Please register to obtain technical support
. Please retain your proof of purchase and warranty
information.
To register your product, get product support or obtain product information and product
documentation, go to http://www.NETGEAR.com
. If you do not have access to the World Wide
Web, you may register your product by filling out the registration card and mailing it to
NETGEAR customer service.
You will find technical support information at:
through the customer service area. If you want to contact technical
support by telephone, see the support information card for the correct telephone number for your
country.
© 2005 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR is a registered trademark of NETGEAR, INC. Windows is a registered trademark of Microsoft
Corporation. Other brand and product names are trademarks or registered trademarks of their respective
holders. Information is subject to change without notice. All rights reserved.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the
right to make changes to the products described in this document without notice. NETGEAR does not
assume any liability that may occur due to the use or application of the product(s) or circuit layout(s)
described herein.
Modifications made to the product, unless expressly approved by Netgear, could void the user’s authority to
operate the equipment. NETGEAR does not assume any liability that may occur due to such condition.
Page 3 / 128
July 2005 v3.0
iii
Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
This device may not cause harmful interference.
2.
This device must accept any interference received, including interference that may cause undesired
operation.
Placement and Range Guidelines
Indoors, computers can connect over 802.11 wireless networks at a maximum range of 500 feet (152.4 m)
for 802.11b devices. However, the operating distance or range of your wireless connection can vary
significantly, based on the physical placement of the wireless access point.
For best results, identify a location for your wireless access point according to these guidelines:
Away from potential sources of interference, such as PCs, large metal surfaces, microwaves, and 2.4 GHz cordless
phones.
In an elevated location such as a high shelf that is near the center of the wireless coverage area for all mobile
devices.
Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly
connect to the wireless access point.
To meet FCC and other national safety guidelines for RF exposure, the antennas for this device must be
installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons. Further, the antennas shall
not be colocated with other transmitting structures.
Tested to Comply
with FCC Standards
FOR HOME OR OFFICE USE
NETGEAR ProSafe Wireless Access Point
FCC ID: PY3WG302
Page 4 / 128
July 2005 v3.0
iv
FCC Statement
DECLARATION OF CONFORMITY
We Netgear,
4500 Great America Parkway
Santa Clara, CA 95054, USA
Tel: +1 408 907 8000
declare under our sole responsibility that the product(s)
WG302
(Model Designation)
802.11g ProSafe Wireless Access Point
(Product Name)
complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
Page 5 / 128
July 2005 v3.0
v
Reorient or locate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Warning for North America, and Australia
Warning! To meet FCC and other national safety guidelines for RF exposure, the antennas for this device
(see below) must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons.
Further, the antennas shall not be colocated with other antenna or radio transmitter.
Antenna Statement for North America and Australia
In addition to its own 2 antennas, the WG302 device has been approved for use with the following
detachable antennas and antenna cables:
* WG302 maximum radiated power in North America and Australia: 20 dBm – cable loss + antenna gain
Please go to
www.netgear.com/go/wg302_fcc
for an updated list of wireless accessories approved to be used
with the WG302 in North America and Australia.
Industry Canada Compliance Statement
This Class B Digital apparatus meets all the requirements of the Canadian Interference Causing Equipment
Regulations ICES 003.
Cet appareil numerique de classe B respecte les exigences du reglement du Canada sur le materiel brouilleur
NMB-003.
The device is certified to the requirements of RSS-210 for 2.4 GHz spread spectrum devices. The use of this
device in a system operating either partially or completely outdoors may require the user to obtain a license
Approved
Antennas
Antenna Gain and
type
Approved Antenna
Cable
Antenna Cable
Length
Maximum
Transmitted Power
NETGEAR
ANT24D18
18 dBi, directional
outdoor/indoor
NETGEAR
ACC-10314-01 thru 05
1.5 m
to 30 m
19 dBm + 18 dBi ant.
NETGEAR
ANT2409
9 dBi, omnidirectional
outdoor/indoor
NETGEAR
ACC-10314-01 thru 05
1.5 m
to 30 m
19 dBm + 9 dBi ant.
NETGEAR
ANT24O5
5 dBi, ceiling/wall
indoor
NETGEAR
ACC-10314-01 thru 05
1.5 m
to 30 m
19 dBm + 5 dBi ant.